View Source Changelog
v1-1-0-2022-12-31
v1.1.0 - 2022-12-31
- Changes
- Remove Erlang convenience functions since no one used them
- Require Elixir 1.10 or later. Previous versions probably work, but won't be supported. This opens up the possibility of using Elixir 1.10+ features in future releases.
v1-0-1-2022-7-26
v1.0.1 - 2022-7-26
- Bug fixes
- On at least one device, the pin direction reported by Linux does not match the actual pin direction. This release forces the pin direction for inputs. It cannot do this for outputs, since setting a pin to output has a side effect on the pin state. This technically is a bug in a Linux driver port, but it was harmless to workaround for inputs so that's what's done. Thanks to @pojiro for investigating and fixing this issue.
v1-0-0-2021-10-20
v1.0.0 - 2021-10-20
This release only changes the version number. No code has changed.
v0-4-8
v0.4.8
This release only has doc and build output cleanup. No code has changed.
v0-4-7
v0.4.7
- Bug fixes
- Fix hang when unloading the NIF. This bug caused
:init.stop
to never return and anything else that would try to unload this module. - Fix C compiler warnings with OTP 24
- Fix hang when unloading the NIF. This bug caused
The minimum Elixir version has been changed from 1.4 to 1.6. Elixir 1.4 might still work, but it's no longer being verified on CI.
v0-4-6
v0.4.6
- Bug fixes
- Fix quoting issue that was causing failures on Yocto. Thanks to Zander Erasmus for this.
v0-4-5
v0.4.5
- Bug fixes
- Opening a GPIO to read its state won't clear the interrupt status of another listener. Registering for interrupts a second time will still clear out the first registree, though. That's a limitation of the interface. However, for debugging, it can be nice to look at a GPIO without affecting the program and this change allows for that.
v0-4-4
v0.4.4
- Bug fixes
- Add -fPIC to compilation flags to fix build with
nerves_system_x86_64
and other environments using the Musl C toolchains
- Add -fPIC to compilation flags to fix build with
v0-4-3
v0.4.3
Bug fixes
- Fix GPIO glitch suppression when interrupts were enabled. Glitch suppression
filters out transitions on a GPIO line that are too fast for Linux and the
NIF to see both the rising and falling edges. Turning it off synthesizes
events. You can identify synthesized events since they have the same
timestamp to the nanosecond. See
Circuits.GPIO.set_interrupts/3
.
- Fix GPIO glitch suppression when interrupts were enabled. Glitch suppression
filters out transitions on a GPIO line that are too fast for Linux and the
NIF to see both the rising and falling edges. Turning it off synthesizes
events. You can identify synthesized events since they have the same
timestamp to the nanosecond. See
Improvement
- It's possible to enable the "stub" on Linux by setting
CIRCUITS_MIX_ENV=test
. This can be useful for unit testing code that uses Circuits.GPIO. Thanks to Enrico Rivarola for adding this!
- It's possible to enable the "stub" on Linux by setting
v0-4-2
v0.4.2
- Bug fixes
- Fix pullup/pulldown support for the Raspberry Pi 4
v0-4-1
v0.4.1
- Bug fixes
- Fix a race condition on Raspbian where Circuits.GPIO would try to open the GPIO sysfs file before udev had a chance to fix its permissions.
- Fix RPi platform detection on Raspbian so that pull-ups/pull-downs work without passing any flags.
v0-4-0
v0.4.0
The GPIO interrupt notification messages have been changed for consistency with
other circuits projects. The initial element of the tuple is now
:circuits_gpio
, so messages will look like:
{:circuits_gpio, 19, 83268239, 1}
Please update your project if you call set_interrupts/2
.
No more backwards incompatible changes are expected until after 1.0.
v0-3-1
v0.3.1
- Bug fixes
- Build C source under the
_build
directory so that changing targets properly rebuilds the C code as well as the Elixir.
- Build C source under the
v0-3-0
v0.3.0
- New features
- Support
pull_mode
initializion inopen/3
.
- Support
v0-2-0
v0.2.0
- New features
- Add support for opening GPIOs to an initial value or to not change the value. This removes a glitch if you want the GPIO to start out high (the default was low) or if you want the GPIO to keep its current value.
v0-1-0
v0.1.0
Initial release to hex.