Settings View Source Elixir Circuits - I2C

Circuits.I2C lets you communicate with hardware devices using the I2C protocol.

If you're coming from Elixir/ALE, check out our porting guide.

getting-started

Getting started

If you're using Nerves or compiling on a Raspberry Pi or other device with I2C support, then add circuits_i2c like any other Elixir library:

def deps do
  [{:circuits_i2c, "~> 1.0"}]
end

Circuits.I2C doesn't load device drivers, so you may need to load them beforehand. If you are using Nerves on a supported platform, this is enabled for you already. If using Raspbian, the Adafruit Raspberry Pi I2C instructions may be helpful.

Internally, it uses the Linux "i2cdev" interface so that it does not require board-dependent code.

i2c

I2C

An Inter-Integrated Circuit (I2C) bus supports addressing hardware components and bidirectional use of the data line.

The following shows a bus IO expander connected via I2C to the processor.

The protocol for talking to the IO expander is described in the MCP23008 Datasheet. Here's a simple example of using it.

# On the Raspberry Pi, the IO expander is connected to I2C bus 1 (i2c-1).
# Its 7-bit address is 0x20. (see datasheet)
iex> alias Circuits.I2C
Circuits.I2C
iex> {:ok, ref} = I2C.open("i2c-1")
{:ok, #Reference<...>}

# By default, all 8 GPIOs are set to inputs. Set the 4 high bits to outputs
# so that we can toggle the LEDs. (Write 0x0f to register 0x00)
iex> I2C.write(ref, 0x20, <<0x00, 0x0f>>)
:ok

# Turn on the LED attached to bit 4 on the expander. (Write 0x10 to register
# 0x09)
iex> I2C.write(ref, 0x20, <<0x09, 0x10>>)
:ok

# Read all 11 of the expander's registers to see that the bit 0 switch is
# the only one on and that the bit 4 LED is on.
iex> I2C.write(ref, 0x20, <<0>>)  # Set the next register to be read to 0
:ok

iex> I2C.read(ref, 0x20, 11)
{:ok, <<15, 0, 0, 0, 0, 0, 0, 0, 0, 17, 16>>}

# The operation of writing one or more bytes to select a register and
# then reading is very common, so a shortcut is to just run the following:
iex> I2C.write_read(ref, 0x20, <<0>>, 11)
{:ok, <<15, 0, 0, 0, 0, 0, 0, 0, 0, 17, 16>>}

# The 17 in register 9 says that bits 0 and bit 4 are high
# We could have just read register 9.

iex> I2C.write_read(ref, 0x20, <<9>>, 1)
{:ok, <<17>>}

faq

FAQ

how-do-i-debug

How do I debug?

The most common issue is communicating with an I2C for the first time. For I2C, first check that an I2C bus is available:

iex> Circuits.I2C.bus_names
["i2c-1"]

If the list is empty, then I2C is either not available, not enabled, or not configured in the kernel. If you're using Raspbian, run raspi-config and check that I2C is enabled in the advanced options. If you're on a BeagleBone, try running config-pin and see the Universal I/O project to enable the I2C pins. On other ARM boards, double check that I2C is enabled in the kernel and that the device tree configures it.

Once an I2C bus is available, try detecting devices on it:

iex> Circuits.I2C.detect_devices()
Circuits.I2C.detect_devices
Devices on I2C bus "i2c-1":
 * 64  (0x40)
 * 112 (0x70)

2 devices detected on 1 I2C buses

The return value here is a list of device addresses that were detected. It is still possible that the device will work even if it does not detect, but you probably want to check wires at this point. If you have a logic analyzer, use it to verify that I2C transactions are being initiated on the bus.

i2c-seems-slow-what-could-be-wrong

I2C seems slow. What could be wrong?

I2C buses are usually run at 100 kbit/s or 400 kbit/s. Many devices support higher speeds. The tradeoff is that higher speeds are sometimes don't work as well especially if you're using jumper cables to connect parts together. The Raspberry Pi runs the I2C bus at a low speed - probably for this reason.

Other things to check:

• Can you reduce the reads and writes? I2C devices let you read or write many bytes at the same time. Each transaction has overhead so minimizing transaction helps.
• Can you reduce the total number of bytes in each transaction? For example, do you need to read a particular register? Is there a mode that the device can be put it so that it only returns useful data?
• Can a write and read be combined? The Circuits.I2C.write_read function is more efficient than a separate write followed by a read.
• Does the device support a queue mode? Some devices have internal queues that allow the host to copy out more than one sample each time.

where-can-i-get-help

Where can I get help?

The hardest part is communicating with a device for the first time. The issue is usually unrelated to Circuits.I2C. If you expand your searches to include Python and C forums, you'll frequently find the answer.

If that fails, try posting a question to the Elixir Forum. Tag the question with Nerves and it will have a good chance of getting to the right people. Feel free to do this even if you're not using Nerves.

can-i-develop-code-that-uses-circuits-i2c-on-my-laptop

Can I develop code that uses Circuits.I2C on my laptop?

You'll need to fake out the hardware. Code to do this depends on what your hardware actually does, but here's one example:

• Compiling and testing Elixir Nerves on your host machine

Please share other examples if you have them.

will-it-run-on-arduino

Will it run on Arduino?

No. This only runs on Linux-based boards. If you're interested in controlling an Arduino from a computer that can run Elixir, check out nerves_uart for communicating via the Arduino's serial connection or firmata for communication using the Arduino's Firmata protocol.

license

License

Code from the library is licensed under the Apache License, Version 2.0.